Low Voltage & Cabling
Structured cabling, certified and labeled, including the mess we did not create
Cat6 and Cat6A installed to standard, every run tested and certified, both ends labeled to a consistent scheme, and a server room you can actually work in.
Open the closet in a typical office and you find fifteen years of archaeology
Unlabeled cables, patch cords running across ceiling tiles, a switch balanced on a shelf, and at least one cable nobody dares unplug because nobody knows what it does. That is the normal state of things, and it is not just ugly.
It is downtime waiting to happen, and it makes every future service call slower and more expensive. When something breaks in an undocumented closet, the first hour goes to tracing what is connected to what before anyone can begin fixing anything. You pay for that hour every single time.
We do it properly. Cabling installed to standard with correct bend radius and separation from electrical, every run certified with a tester and the results handed to you, both ends labeled to a consistent scheme, a patch panel that maps to a documented port schedule, and a rack where airflow works and you can reach the equipment without moving three other things first.
Beyond data cabling we handle the rest of the low-voltage work most offices need: camera runs, access control, TV and display mounts, and speaker or paging wiring. Same standard, same labeling, same documentation.
You probably need this if
- Your server closet has unlabeled cables nobody wants to touch
- Patch cords are running across ceiling tiles or along the floor
- You are moving, expanding, or building out a new suite
- Nobody knows which jack maps to which switch port
- You need camera, access control, or display runs installed cleanly
- A previous installer left no documentation of any kind
What is included
Deliverables
What you actually get, in writing
Not a vague promise of support. Specific artifacts you can point at, hand to an auditor, or take with you if you ever leave.
Port schedule and labeling map
Every jack mapped to a panel port and a switch port, labeled identically at both ends. Future service calls get measurably shorter and cheaper.
Certification test results
Documented pass results for every run, so a future performance complaint can be isolated to equipment instead of argued about.
As-built cabling documentation
Drop locations marked on a floor plan, including camera, access control, and display runs, so the next install does not start with a scavenger hunt.
Rack elevation drawing
What is mounted where, with power and uplink paths documented. Genuinely useful at 2 a.m.
Before and after photos
Not vanity. Proof of what changed, and an honest record of what you inherited from whoever came before.
Warranty and standards compliance
Installed to manufacturer specification so component warranties remain intact rather than voided by the install.
Questions
Questions about this service
Do you do cabling as a standalone project, or only for managed clients?
Standalone is completely fine, and it is often how a relationship starts. Plenty of clients first hired us to clean up a server closet or cable a new suite, then moved to managed services later because they liked how the documentation was handled. There is no requirement to bundle anything.
Our server room is genuinely embarrassing. Is that a problem?
It is the job, and honestly the bad ones are the most satisfying. We have untangled closets that took two full days just to trace and identify before any real work started. There is no judgment here. You will get before and after photos along with the documentation, and most clients end up sending them to people.
Can you run cable in an occupied medical or dental office?
Yes, and we schedule around your patient flow rather than the other way around. That usually means evenings, early mornings, or a scheduled closure day. We contain dust, protect surfaces, and clean up at the end of each session, because a practice cannot see patients in a construction zone.
Cat6 or Cat6A? Does it matter?
It depends on distance and what you expect to run over it. Cat6 handles 10 gigabit at shorter distances and is adequate for most office runs. Cat6A holds 10 gigabit across a full 100-meter run and has better crosstalk shielding, which matters in dense bundles or near electrical. We will recommend based on your building rather than defaulting to whichever we have on the truck.
What about cameras, access control, and TVs?
We run and terminate low voltage for all of it. For cameras and access control we handle the cabling and the network side, and we coordinate directly with your security vendor on their equipment so you are not stuck between two companies each pointing at the other.
Do you handle new construction?
Yes, including rough-in coordination with your general contractor and electrician. Getting involved before drywall is dramatically cheaper than adding drops afterward, so if you are building or doing a tenant build-out, call earlier than feels necessary.
Want to know where you stand right now?
The assessment documents your environment, scores it against a modern baseline, and hands you a written report you keep either way.
No pressure, no obligation. If we are not the right fit we will tell you and point you somewhere better.